MODULAR WET-FLOOR

 

DRAINAGE COMPONENT

Manufactured from tough ABS plastic, the Drainage Component is the central element of the Modular Wet-Floor, once its position has been decided, the remainder of the system is built around it.

Forming a base for the Linear Drain, the Drainage Component has a 1mm gradient towards the centre and can be installed in either an offset or central position within the shower area, or neatly up against the wall to create a sleek and unobtrusive wall drain*.
The Drainage Component can be easily trimmed by up to 200mm off each end using a hand saw and is secured using the pre-drilled screw ports.

Two Drainage components can also be butted together to create a larger wetroom area.

*When installed with the Wall Grill, the Drainage Component width is reduced by 80mm, to 220mm

The Trap
The trap has an adjustable ball joint and comes with removable dip-tube.
For ease of installation it can be fitted anywhere within the central section of the Drainage Component, making it simple to avoid joists and other such obstructions.

 

 

---

NUMBER OF TRAPS

A single trapped Linear Screed Drain has a flow rate of up to 27 L/min* with the support brackets on either side. When a higher flow rate is required a double trap version is available, allowing up 50 L/min*. For higher flow rates a third trap can be installed giving up to 68 L/min*.

---

TAPERED BOARD

The Tapered Boards are manufactured from XPS foam with a mineral coating, making them both lightweight and easy to handle, whilst maintaining good thermal properties and compressive strength. Each board is 1200mm long and tapered from 22mm to 11mm, giving a consistent gradient every time.
Available in five widths, the boards can be easily trimmed to size using a hand saw and should be secured with the fixing washers supplied, at a minimum of 300mm centres. The system is designed with versatility in mind and can be installed in a number of different configurations. Click Here for the most common layouts.

Using a combination of boards, either a one way fall towards the wall, or a two way fall with a central or offset drain can be created. Two or more Tapered Boards can also be butted together to create a larger wetroom area. A 280mm x 300mm infill panel is available for use in certain configurations.

	• Designed for timber floors • One or two way fall • Wetroom area can be varied to suit • Easily trimmed • Fixing washers included • Quick and easy to install • Ideal for large format tiles

TAPERED BOARD ARE AVAILABLE IN 5 STANDARD SIZES

A		B
300mm	x	1200mm
500mm	x	1200mm
700mm	x	1200mm
1000mm	x	1200mm
1200mm	x	1200mm
INFILL PANEL		2800mm X 300mm

---

GRILL TYPE

There are two types of grill available within the Modular Wet-Floor system, both are designed to fit onto the Drainage Component. Floor Grill For installation in either an offset or central position within the shower area. Grill width 58mm
Wall Grill For installation against the wall.Grill width 86mm

---

GRILL LENGTHS

The Drainage Component is manufactured with one trough size at 660mm, all lengths of grill are then fitted onto this trough. The grill is available in four standard sizes; two grills can be butted together to create a larger wetroom area (excluding 600mm grill). Bespoke grills can be manufactured for sizes in between and over those that are standard. Please contact our technical team to discuss your requirements.

 

The Linear Screed Drain is available in four standard sizes: • 600mm x 58mm • 800mm x 58mm • 1000mm x 58mm • 1200mm x 58mm		The grill is height adjustable in 1mm increments to suit tile thicknesses of 6mm to 20mm. Additional spacers are available upon request for tiles thicker than 20mm.		The Wall Grill is width adjustable to allow for different wall tile thicknesses.

---

GRILL FINISH

The grill is available in various different finishes. All are manufactured in 316 marine grade stainless steel, ensuring a stunning high quality finish. Type A Solid Grill is supplied as standard unless otherwise specified.

Type A - Solid Grill: Grained stainless steel with a 3mm gap around the grill for a sleek stylish finish.

Type B – Oblong Slots: Three rows of oblong slots in a highly polished mirrored stainless steel finish.

Type C – Square Holes: Three rows of squares in a grained stainless steel finish.

 

---

CLICK HERE TO VIEW TYPICAL LAYOUTS

---

PRODUCT DETAILS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

---

HOW TO SPECIFY

To specify your Modular Wet-Floor first decide the layout of your wetroom, then simply follow the three step process:

Step		Select the required number of Drainage Components and Traps
Step		Select the required number and size of Tapered Boards
Step		Select the required Floor or Wall Grill

Note: The Drainage Component and Tapered Boards can be easily trimmed on-site.

Two Drainage Components and Grills can be butted together to create a larger wetroom area.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

---

MEMBRANE

 

 

 

 

 

 

 

 

 

 

It is essential that the floor is waterproofed or ‘tanked’ using the following membranes.
For timber floors we would recommend the Tilesafe membrane is applied to the entire wetroom floor.
FWM should then be applied to the walls of the shower area plus an additional 300mm and overlapped onto the Tilesafe Reinforcing Tape.

---

IN DETAIL

 

 

 

 

 

 

 

 

 

 

 

 

 

	View Line Drawings Online		Product Downloads	Go to the top of this page.
	Modular WetFloors Brochure		Full Brochure